Pre-summer cooling checklist for 2027: getting ACs and equipment rooms ready before the heat

Peak demand and heatwaves arrive together. A pre-summer checklist for 2027 to get ACs, precision cooling and equipment rooms ready before April.

Rajiv Tomar, DirectorPublished 5 min read

Key takeaways

  • Service cooling in February and March. By April, technicians and parts are in short supply.
  • Dirty coils and filters cost capacity exactly when you need it most.
  • Equipment rooms need a temperature alarm, not just a thermostat.
  • Plan for a unit failing on the hottest day: know your backup.

At three in the afternoon on a day in May, the outdoor unit serving a control room has been sitting in full sun since ten. Its condenser coil is matted with a winter’s worth of dust and cottonwood fluff. Head pressure climbs, the compressor trips on its high-pressure switch, restarts, trips again. Inside, the room creeps past 30 °C and a drive cabinet starts throwing overtemperature warnings. The service company can come on Thursday.

Every part of that story is preventable, and almost all of the prevention is cheap if it happens in February or March. This checklist covers what to do, in order, so your cooling is ready before the heat rather than repaired during it.

Why the weeks before summer matter

Summer is when cooling works hardest and when the grid is under most strain. India’s peak power demand reached 256.1 GW on 25 April 2026, an all-time high at that point (PIB). The India Meteorological Department’s heat outlook, issued at the end of March 2026, expected above-normal heatwave days from April to June in parts of east, central and north-west India. Look out for the 2027 outlook around the same time.

That means three things for you. Your units run near full capacity for weeks. Voltage dips and power cuts are more likely. And every service company in your city is busy at once. Work done before April gets done properly; work left until May gets done in a hurry, if at all.

Outdoor units

Outdoor units reject the heat. If they can’t, nothing else matters.

  • Clean the condenser coil. Remove dust, leaves and fluff with a soft brush and low-pressure water or a suitable coil cleaner, from the inside out where the design allows. Don’t use high-pressure jets that flatten the fins.
  • Straighten bent fins with a fin comb where large areas are flattened.
  • Check airflow. At least the clearance the manufacturer specifies on every side and above. Remove stored material, overgrown plants and anything that makes hot air recirculate back into the coil.
  • Look at the location. Units packed tightly together on a roof, or in an enclosed courtyard, can end up breathing each other’s exhaust air. Shade from a well-ventilated canopy can help, as long as it doesn’t restrict airflow.
  • Check the fan. It should spin freely, with no wobble, noise or damaged blades.
  • Check mountings and pipe insulation. Loose mountings cause vibration and pipe damage. Cracked or missing insulation on the suction line costs capacity.

Indoor units and drains

  • Clean or replace filters. A clogged filter cuts airflow and capacity, and can freeze the coil.
  • Inspect the evaporator coil for dust and mould, and clean it if needed.
  • Clear the drain. Flush the drain tray and line. A blocked drain overflows when the unit starts removing serious amounts of moisture, and water over an equipment room is the last thing you need.
  • Check the blower for dirt build-up on the wheel, which reduces airflow.
  • Check remotes and controllers, and set sensible set points. Star-labelled room ACs have been shipped with a 24 °C default setting since 1 January 2020 (PIB). The Bureau of Energy Efficiency says each 1 °C higher setting saves about 6% of electricity (BEE). Comfort areas rarely need much colder than that; equipment rooms should follow the equipment manufacturer’s limits.

Electrical checks

Many summer breakdowns are electrical, not mechanical.

  • Capacitors. Swollen, leaking or out-of-tolerance run capacitors are a common cause of compressors and fans failing to start on hot days. A technician can measure capacitance against the rating.
  • Contactors. Look for pitted or burnt contacts that can stick or chatter.
  • Terminals. Check tightness and look for discolouration at terminals in the outdoor unit and supply isolator. A loose terminal runs hot and gets worse under summer currents.
  • Supply voltage. Note the voltage at the unit under load. Persistent low voltage makes compressors draw more current and run hotter. If you see it, talk to your electrical team.
  • Protection settings. Confirm that overload and high-pressure protection work as intended. Never bypass a protection device to keep a unit running.

Refrigerant

Ask a trained technician to check the system’s operating pressures and temperatures and look for signs of leaks: oily marks on joints, ice on the wrong parts, or a unit that “needed gas last year”. A leaking system should be repaired and then charged to the nameplate quantity. Topping it up every summer wastes refrigerant and hides the fault.

Equipment and control rooms

Equipment rooms need more than comfort cooling.

  • Fit a temperature alarm. A thermostat controls a unit. An alarm tells a person when the room is too hot, even if the unit thinks it is working. Send the alarm to someone who can act at night and on holidays.
  • Log temperature and humidity. A simple logger shows how the room behaves through the afternoon peak and overnight. Our article on dehumidification for electronics explains why humidity matters too.
  • Check precision cooling units to the manufacturer’s schedule: filters, humidifier, condensate pumps and alarms.
  • Manage airflow. Keep cabinet doors closed, fit blanking panels, and don’t stack boxes in front of supply grilles or return air paths.
  • Check panel coolers and filter fans on control panels in the same round. They fight the same heat.

A plan for the hottest day

Assume one unit will fail at the worst moment, and decide now what happens next.

  1. Know your redundancy. If a room has two units, can one carry the load alone at peak outdoor temperature? Test it in March.
  2. Rotate standby units so they are proven to work, not just assumed to.
  3. Have a fallback. Portable cooling, a plan to shed non-essential load in the room, or a shutdown order for equipment if temperature passes a set point.
  4. Keep contacts ready. Who will you call, and do they know your site and your units?
  5. Keep a few common spares if your site depends on cooling, such as capacitors and contactors that match your units.

If you would like this done for you, we service split, package, ducted and precision cooling for commercial buildings and equipment rooms, and can put your units on a planned schedule with a report after each visit. See our cooling and heating services or request a quote for a pre-summer service.

General guidance based on common engineering practice. Always follow the equipment manufacturer’s instructions and your site’s safety procedures.

Add RATOM as a preferred source on Google

Related services

How we can help.

Keep reading

More from our engineers.

Got a unit that’s down?

Tell us the make, model and fault, and we’ll reply within one working day with questions or next steps.